View AP-SDM008G1PANS-EM_8032154.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

halogen free sata - disk module 22p/90d - m specification january 25 , 2010 version 1. 1 apacer technology inc. 4 th fl., 75 xintai 5 th rd ., sec.1, hsichih, taipei hsien 221 , taiwan tel: +886 - 2 - 269 8 - 2888 fax: +886 - 2 - 269 8 - 2889 www.apacer.com
s ata - disk module a p - sdm xxxx1pa x s - em 1 ? 20 10 apacer technology inc. rev . 1 . 1 features: ? standard serial ata 2.5 (gen. 2) C serial ata 2.5 (gen. 2) C sata , 3.0 gbps C ata - compatible command set ? capacities C standard: 4, 8, 16, 3 2 , and 64 gb C high speed: 4, 8, 1 6 , and 32 gb ? performance C burst read/write: 300 mb/sec C sustained read: up to 95 mb/sec C s ustained write: up to 50 mb/sec ? intelligent endurance design C built - in h ardware bch ecc , c orrect ing 8 - bit or 15 - bit error per 512 - byte data sector C global wear - leveling scheme together with dynamical block allocation to significantly increase the lifetime of a flash device and optimize the disk performance C flash bad - block management C s.m.a.r.t. technology ? nand flash type: mlc ? da ta integrity under power - cycling C no battery required for data storage ? temperature C o perating : 0c to 70c C storage: - 40 c to 100 c ? supply v oltage C 5.0 v 5% ? low power consumption C active mode: 260 ma C idle mode: 130 ma ? c onnector type C 7 - pin signal connector C 15 - pin power connector ? halogen free
s ata - disk module a p - sdm xxxx1pa x s - em 2 ? 20 10 apacer technology inc. rev . 1 . 1 t able of contents 1 . product desc ription ................................ ................................ ................................ . 3 1.1 introduction ................................ ................................ ................................ ............................. 3 1.2 functional block diagram ................................ ................................ ................................ ...... 3 1.3 ata mode support ................................ ................................ ................................ .................. 4 1.4 capacity specification ................................ ................................ ................................ ............ 4 1.5 performances ................................ ................................ ................................ .......................... 4 1.6 pin assignments ................................ ................................ ................................ ..................... 5 2. software interface ................................ ................................ ................................ .... 6 2.1 command set ................................ ................................ ................................ .......................... 6 3. flash management ................................ ................................ ................................ ... 8 3.1 error correction/detection ................................ ................................ ................................ ..... 8 3.2 bad block management ................................ ................................ ................................ .......... 8 3.3 wear leveling ................................ ................................ ................................ .......................... 8 3.4 power failure management ................................ ................................ ................................ .... 8 3.5 quick erase ................................ ................................ ................................ ............................. 8 3.6 s.m.a.r.t. technology ................................ ................................ ................................ ............ 9 4. environmental specifications ................................ ................................ ............... 10 4.1 environments ................................ ................................ ................................ ........................ 10 5. electrical specification ................................ ................................ ........................... 11 6. physical characteristics ................................ ................................ ......................... 12 6.1 dimension ................................ ................................ ................................ ............................. 12 7. product ordering information ................................ ................................ ............... 12 7. product ordering information ................................ ................................ ............... 13 7.1 pro duct code designations ................................ ................................ ................................ .. 13 7.2 valid combinations ................................ ................................ ................................ ............... 14
s ata - disk module a p - sdm xxxx1pa x s - em 3 ? 20 10 apacer technology inc. rev . 1 . 1 1 . p roduct description 1.1 introduction apacers sata disk module ( s dm ) is a solid - state disk (ssd) drive that contains a controller, embedded firmware, and f lash m edia along with a male connect or. using nand flash memory devices, t he sdm drive interfaces with the host allowing data to be seamlessly transferred between the host and the f lash devices . the sdm drive is designed with a single - chip controller , offer ing capacit ies of up to eight gigabytes and provid ing full support for the sata high - speed interface standard. it can operate at sustained access rates of up to thirty five megabytes per second, which is much fast er than any other competitor in the market . in addition to buffer management through dynamical allocation, the sdm adopt s the static wear - leveling scheme to allow uniform use of all storage blocks , ensur ing that the lifetime of a flash media can be significantly increased and the disk performance is optimized as well. the sdm provides the s.m.a.r.t. feature complies with the sata rev. 2. 6 , ata/atapi - 7 specifications and uses the standard smart command b0 h to read data from the drive. this feature protects the user from unscheduled downtime by monitoring and storing critical drive performance. 1. 2 function al block diagram the sdm drive inclu de s a single - chip sata c ontroller and the f lash m edia , as well as the sata standard interface. the c ontroller integrates the flash management unit with the controller itself to support multi - channel, multi - bank flash arrays. figure 1 - 1 shows the functional block diagram. f igure 1 - 1 apacer sdm block diagram
s ata - disk module a p - sdm xxxx1pa x s - em 4 ? 20 10 apacer technology inc. rev . 1 . 1 1. 3 ata mode support the sdm provides ata m ode s upport as follows: ? u p to pio mode - 4 ? u p to multi word dma mode - 2 ? u p to u dma mode - 5 1. 4 capacity specification capacity s pecification of the sdm product family is available as shown in t able 1 - 1 . it lists the specific capacity , the default number s of logical cylinders and heads, and the number of logical sectors per track for each product line. table 1 - 1 c apacity s pecification capacity total bytes cylinders heads sectors max lba 4 gb 4,021,936,128 7793 16 63 7,855,344 8 gb 8,061,419,520 15620 16 63 15,744,960 16 gb 16,139,681,792 1638 3 16 63 31,522,816 1 32 gb 32,296,140,800 16383 16 63 63,078,400 1 64 gb 64,609,058,816 16383 16 63 126,189,568 1 1 cylinders, h eads or s ectors are not applicable for these capacities. only lba addressing applies. 1. 5 performance s p erformance s of the sdm are shown in table 1 - 2 and table 1 - 3. table 1 - 2 standard models p erformance specification capacity performance 4gb 8gb 16gb 32gb 64gb sustained read (mb/s) 44 45 46 4 6 94 sustained write (mb/s) 14 12 25 27 50 table 1 - 3 high speed models p erformance specification capacity performance 4gb 8gb 16gb 32gb sustained read (mb/s) 75 94 94 93 sustained write (mb/s) 17 25 25 51
s ata - disk module a p - sdm xxxx1pa x s - em 5 ? 20 10 apacer technology inc. rev . 1 . 1 1.6 pin assignments t able 1 - 4 : signal segment t able 1 - 5 : power segment name type description pin signal/description s1 gnd p1 not used (3.3v) s2 rxp + differential receive signal p2 not used (3.3v) s 3 rxn - differential receive signal p3 not used (3.3v) s4 gnd p4 ground s5 txn - differential transmit signal p5 ground s6 txp + differential transmit signal p6 ground s7 gnd p7 5v p8 5v p9 5v p10 ground p11 ground p12 g round p13 not used (12v) p14 not used (12v) p15 not used (12v)
s ata - disk module a p - sdm xxxx1pa x s - em 6 ? 20 10 apacer technology inc. rev . 1 . 1 2. software interface 2.1 command set table 2 - 1 summarizes the ata command s supported by sdm. t able 2 - 1: command set (1 of 2) command code fr 1 sc 2 sn 3 cy 4 dh 5 lba 6 check - power - mode e5h - - - - d 8 - execute - drive - diagnostic 90h - - - - d - flush - cache e7h - - - - d - identify - drive ech - - - - d - idle e3h - y - - d - idle - immediate e1h - - - - d - initialize - drive - parameters 91h - y - - y - read - dma c8h or c9h - y y y y y read - multiple c4h - y y y y y read - sector(s) 20h or 21h - y y y y y read - verify - sector(s) 40h or 41h - y y y y y recalibrate 1 0 h - - - - d - security - disable - password f6h - - - - d - security - erase - prepare f3h - - - - d - security - erase - unit f4h - - - - d - security - freeze - lock f5h - - - - d - se curity - set - password f1h - - - - d - security - unlock f2h - - - - d - seek 7xh - - y y set - features efh y 7 - - - d -
s ata - disk module a p - sdm xxxx1pa x s - em 7 ? 20 10 apacer technology inc. rev . 1 . 1 t able 2 - 1: command set (2 of 2) command code fr 1 sc 2 sn 3 cy 4 dh 5 lba 6 set - multiple - mode c6h - y - - d - sleep e6h - - - - d - smart b0h y y y y d standby e2h - - - - d - standby - lmmediate e0h - - - - d - write - dma cah - y y y y y write - multiple c5h - y y y y y write - sector(s) 30h - y y y y y 1. fr - features register 2. sc - sector count register 3. sn - sector number re gister 4. cy - cylinder registers 5. dh - drive/head register 6. lba - logical block address mode s upported (see command descriptions for use) 7. y - the register contains a valid parameter for this command. 8. for the drive/head register: y means both the sdm and head parameters are used d means only the sdm parameter is valid and not the head parameter
s ata - disk module a p - sdm xxxx1pa x s - em 8 ? 20 10 apacer technology inc. rev . 1 . 1 3. flash management 3 . 1 error correction / d etection the sdm implements a hardware ecc scheme, based on the bch algorithm , to achieve up to 8/15 bit correction per 512 bytes. 3.2 bad block management although bad blocks on the flash media are already identified by the flash manufactur er , they can also be accumulated over time during operation. the controller of sdm maintain s a table that lists those normal blocks with disk data, the free blocks for wear leveling, and bad blocks with errors. when a normal block is detected broken, it is replaced with a free block and listed as a bad block. when a free block is detected broken, it is then r emoved from the fre e block list and marked as a bad block. during device operation, this ensure s that newly accumulated bad blocks are transparent to the host. the device will stop file write service once there are only two fre e blocks left such that the read function is still available for copying the files from the disk into another. 3.3 wear leveling the nand flash devices are limit ed by a certain number of write cycles. when using a fat - based file system, frequent fat table updates are required. if som e area on the flash wears out faster than other s , it would significantly reduce the lifetime of the whole ssd , even if the erase counts of other s are far from the write cycle limit . thus, if the write cycle s can be distributed evenly across the media, the lif e time of the media can be prolonged significantly. th is scheme is called w ear leveling. apacer s w ear - leveling scheme is achieved both via b uffer m anagement and apacer - specific global w ear leveling. they both ensure that the lifetime of the flash media can be increased, and the disk access performance is optimized as well. 3.4 power failure management the low power detection on the controller initiates cached data saving before the power suppl y to the device is too low. this feature prevents the device from c rash and ensure s data integrity during a n unexpected blackout. o nce power was failure before cached data writing back into flash, data in the cache will lost. the next time the power is on, the controller will check these fragmented data segment, and , if necessary, replace them with old data kept in flash until programmed successfully. 3.5 quick erase accomplished by t he secure erase (se) command, which added to the open ansi standards that control disk drives, quick erase is built into the disk dr ive itself and thus far less susceptible to malicious software attacks than external software utilities. it is a positive easy - to - use data destroy command, amounting to electronic data shredding. e xecuting the command causes a drive to internally completel y erase all possible user data. this command is carried out within disk drives, so no additional software is required. o nce executed, neither data nor the erase counter on the device would be recoverable, which blurs the acc uracy of
s ata - disk module a p - sdm xxxx1pa x s - em 9 ? 20 10 apacer technology inc. rev . 1 . 1 device lifespan. the pr ocess to erase will not be stopped until finished while encountering power failure, and will be continued when power is back on. 3.6 s . m . a . r . t . t echnology s.m.a.r.t. is an a cronym for self - monitoring, analysis and reporting technology, an open standard all owing disk drives to automatically monitor their own health and report potential problems. it protects the user from unscheduled downtime by monitoring and storing critical drive performance and calibration parameters . ideally, this should allow tak ing pro active actions to prevent impending drive failure. apacer smart feature follows the sata rev. 2.5, ata/atapi - 7 specifications, using the standard smart command b0h to read data from the drive. a nd based on the sff - 8035i rev. 2.0 specifications, apacer sma rt defines 3 vendor - specified smart attribute ids ( e5 h , e8h - ef h, and f 3h) in the sdm . they represent flash id, good block count, free - list block count, maximum erase count, average erase count , and firmware version information . when the apacer smart utilit y running on the host, it analyzes and reports the disk status to the host before the sdm is in critical condition.
s ata - disk module a p - sdm xxxx1pa x s - em 10 ? 20 10 apacer technology inc. rev . 1 . 1 4. e nvironment al specification s 4.1 environments the sdm environmental specifications f ollow the us military standard mil - std - 810 f , as shown in table 4 - 1. table 4 - 1 sdm environmental specifications (plan) environment speci fication operation 0 c to 70 c temperature storage - 40 c to 100 c h umidity 5 % to 95 % rh ( non - condensing ) sine wave : 5~55~5 hz (x, y, z) random: 10 - 2000 hz, 16.3 g (x, y, z) vibration shock acceleration: 1,500 g, 0.5 ms peak acceleration: 50 g, 11 ms
s ata - disk module a p - sdm xxxx1pa x s - em 11 ? 20 10 apacer technology inc. rev . 1 . 1 5 . electrical specification caution: absolute maximum stress ratings C (applied conditions greater than those listed under absolute maximum stress ratings may cause permanent damage to the device. this is a stre ss rating only and functional operation of the device at these conditions or conditions greater than those defined in t he operational sections of this data sheet is not implied. exposure to absolute maximum stress rating c onditions may affect device reliab ility. table 5 - 1: operating voltage range ambient temperature 5v standard 0c to 70c 4.5 - 5.5v table 5 - 2: a bsolute maximum power pin stress ratings parameter symbol conditions input power v dd - 0.3v min. to 6.5v max. voltage on any pin except v dd with respect to gnd v - 0.5v min. to vdd + 0.5v max.
s ata - disk module a p - sdm xxxx1pa x s - em 12 ? 20 10 apacer technology inc. rev . 1 . 1 6 . physical characteris tics 6.1 dimension unit: mm tolerance: 0.2 5 signal pin 1 power pin 1
s ata - disk module a p - sdm xxxx1pa x s - em 13 ? 20 10 apacer technology inc. rev . 1 . 1 7. pr oduct o rdering information 7.1 product code designations a p C s dm x x x x 1 p a x s C e m environmental specification sata disk module apacer product code capacity : 004g: 4 gb 008g 8 gb 016g : 16 gb 0 32 g : 32 gb 0 64 g 64 gb 004g: 4 gb package modifier 1= 22p / 90d solution version version control apacer brand flash type m: mlc configuration n: standard d: dual channel
s ata - disk module a p - sdm xxxx1pa x s - em 14 ? 20 10 apacer technology inc. rev . 1 . 1 7.2 valid combinations standard type capacity model number 4gb ap - sdm004g1pans - em 8 gb ap - sdm00 8 g1pans - em 16 gb ap - sdm0 16 g1pans - em 32 gb ap - sdm0 32 g1pans - em 64 gb ap - sdm0 6 4g1pans - em high speed type capacity model number 4gb ap - sdm004g1pa d s - em 8 gb ap - sdm00 8 g1pa d s - em 16 gb ap - sdm0 16 g1pa d s - em 32 gb ap - sdm0 32 g1pa d s - em note: valid combinations are those products in mass production or wi ll be in mass production. consult your a pacer sales representative to confirm availability of valid combinations and to determine availability of new co mbinations.
s ata - disk module a p - sdm xxxx1pa x s - em 15 ? 20 10 apacer technology inc. rev . 1 . 1 revision history rev ision date description remark 0.1 10/08/2009 preliminary 1. 0 10/26/2009 official release 1.1 01/ 25 /2010 updated all performance figures
s ata - disk module a p - sdm xxxx1pa x s - em 16 ? 20 10 apacer technology inc. rev . 1 . 1 global presence taiwan (headquarters) apacer technology inc. 4 th fl., 75 xintai 5 th rd., sec.1 hsichih, 221 taipei hsien taiwan, r.o.c. tel: +886 - 2 - 269 8 - 2888 fax: +886 - 2 - 269 8 - 28 8 9 amtsales@apacer.com u.s.a. apacer memory america, inc. 386 fairview way, suite102, milpitas, ca 95035 tel: 1 - 408 - 5 18 - 8699 fax: 1 - 408 - 935 - 9611 sa@apacerus.com japan apacer technol ogy corp. 5f, matsura bldg., shiba, minato - ku tokyo, 105 - 0014, japan tel: 81 - 3 - 5419 - 2668 fax: 81 - 3 - 5419 - 0018 jpservices@apacer.com europe apacer technology b.v. europalaan 89 5232 bc 's - hertogenbosch the netherland s tel: 31 - 73 - 645 - 9620 fax: 31 - 73 - 645 - 9629 sales@apacer.nl china apacer electronic (shanghai) co., ltd 1301, no.251,xiaomuqiao road, shanghai, 200032, china tel: 86 - 21 - 5529 - 0222 fax: 86 - 21 - 5206 - 6939 s al es@apacer.com.cn india apacer technologies pvt. ltd. #143, 1st floor, raheja arcade, 5th block kormangala industrial layout, bangalore - 560095, india tel: 91 - 80 - 4152 - 9061 sales_india@apac er.com
mouser electronics authorized distributor click to view pricing, inventory, delivery & lifecycle information: apacer: ? ap-sdm004g1pads-em? ap-sdm008g1pads-em? ap-sdm016g1pads-em? ap-sdm032g1pads-em? ap- sdm064g1pans-em

▲Up To Search▲

Price & Availability of AP-SDM008G1PANS-EM

	To Download AP-SDM008G1PANS-EM Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .